[Gaming NB/DT] Armoury Crate Application Introduction Armoury Crate Introduction (Ver5.0)Armoury Crate Introduction (Ver4.0)Armoury Crate Mobile Version Introduction (Android/ iOS)Armoury Crate - Installation SOPAniMe Matrix™ Display - IntroductionKe...
MyASUS Frequently Asked Question (FAQ)Table of Contents [Phone] MyASUS App - Introduction [Motherboard] MyASUS introduction [Notebook] MyASUS-Unable to reset GPU mode to default value [Notebook] MyASUS - Introduction [Notebook] MyASUS- Settings ...
ASUS Router Plug-n-Share Disks Compatibility List* OS encrypted hard drives are not supported. Wireless RouterModelFirmware versionMaximumPartitionNumberDisk Format & Maximum Partition Size:File Size:FAT32EXT2EXT3EXT4NTFS (Read Only)NTFS (Write...
[Gaming Handheld] Yellow Exclamation Mark Appears in Device Manager After Connecting AMD External GPUIf you encounter a yellow exclamation mark next to the graphics card in Device Manager after connecting an AMD external GPU to your ROG Ally series g...
[AIOT] Flash OS Image by Windows for PE1000N1. Preparing your Environment1. Update Windows version to build 19041 or higher2. Open Windows PowerShell as administrator mode3. Type the command below in PowerShell to enable WSL and Virtual Machine1.dism...
[AIOT] Flash OS Image by Ubuntu for PE1000N1. Recovery Mode1. System Requirement• Linux Host Computer (x86 Ubuntu 18.04 and above)• Micro USB cable2. Enter Force Recovery ModeFor PE1000N Box, the Flash Port is number ❸, and the Force Recovery Button ...
[AIOT] Upgrade to Jetpack 6.1 for PE1100NPlease make sure your OS is Jetpack 6.0$ cat /etc/nv_tegra_release Add the R36.4/JP 6.1$ echo "deb https://repo.download.nvidia.com/jetson/common r36.4 main" | sudo tee -a /etc/apt/sources.list.d/nvidia-l4t-a...
[AIOT] OS Version Information for PE1100NPlease refer to the table below for recommended OS versions and NVIDIA SDK versions for each image versionPE1100N official release versionL4TUbuntuJetPackCUDADeepStream SDKcuDNNTensorRTV1.0.035.3.120.045.1.111...
[AIOT] Console Port Set Up for PE1100NPE1100N console port connect to PC - USB to UART Bridge.When PE1100N console port is connected to a PC, it is possible that a USB to UART Bridge exclamation mark may appear in Device Manager.The baud rate is 1152...
[AIOT] Switch DIO Sop for PE1100NOpen Terminal on the desktopType below command to switch DIOSet one DO Value: sudo dio_out #DO_Num # Value Get one DI Value: sudo dio_in #DO_Num Get all DO Value: sudo dio_out Get all DI Value: sudo dio_in
[AIOT] Check SIM Card Status for PE1100N1. Open Terminal on the desktop 2. Type command ‘sudo PE1100N-config’, if it asks for a password, enter the password set by yourself. Press Enter. 3. Select Ok 4. Select 7. Configuration and press Enter 5. Ch...
[AIOT] LTE Setting Information for PE1100NNOTE : Please insert the SIM card and power on the device.1. Click to open the settings bar at the top right side of the desktop. 2. Click Mobile Broadband Settings. 3. Switch on the Mobile Broadband to enab...
[AIOT] Flash OS Image for PE1100NPE1100N only support flash image via Ubuntu and doesn't support flash image via Windows.1. Recovery Mode1. System Requirement• Linux Host Computer (x86 Ubuntu 18.04 and above)• Micro USB cable2. Enter Force Recovery M...
[AIOT] Console Debug Information for PV100AHow to use Android Debug Bridge (adb)1. Prepare an USB Type-C to Type-A cable.2. Connect your device with USB: Connect cable Type-C side to PV100A and Type-A side to PC.You can verify that your device is con...
[AIOT] Power Ignition Control for PV100ADefault valueItemsDefault delay time (Seconds)Ignition on delay0Ignition off delay0Hard off delay180 Note:When the ignition off delay ends, and the system has not shut down normally for more than 180 sec...
[AIOT] G-Sensor Information for PV100A1. G-Sensor disableOpen adb shell or Terminal $ /MCU_test_tool/gsensor_test disable PASS 2. G-Sensor enableOpen adb shell or Terminal $ /MCU_test_tool/gsensor_test enable PASS 3. G-Sensor readOpen adb shell or ...
[AIOT] COM Setting for PV100A1. Boot up PV100A2. Open terminal3. Using command “PV100A-config” into the setting, shows below:4. Select “OK”5. Select “6 UART” to change protocol (RS232/ RS485)6. Select RS232 or RS4857. Press “OK”8. Press ‘Tab’ to sele...
[AIOT] Build OS Debian for PV100A1. Create an Ubuntu machine environment (Using the following versions : Ubuntu 20.04.)2. Download Debian source code from github (https://github.com/ASUS-IPC/manifest) $ git config --global user.name "Your Name" $ gi...
[AIOT] Source Code Download Link for PV100APlease refer to the following URL to get the source codehttps://github.com/ASUS-IPC/manifest
[AIOT] Flash OS Image Debian for PV100ACase 1. Flash an image in serial download mode (For unbricking)If device is in brick state or is with an empty eMMC, we can use “serial download mode” to flash an image.Flash imagei. Toggle boot_mode switch to “...
