AX3000 update driver failed的問題

[有想過未來世青還叫小翼的問題嗎]

Moderator自己谷歌下update driver failed,沒什麼人說但不代表沒有
06:27:49 acsd: eth6: Selecting 5g band ACS policy
06:27:52 acsd: acsd_main_loop(1062): sync_id: 25035, status:1, misc.error/abort
06:27:52 acsd: eth6: selected channel spec: 0xe09b (149/80)
06:27:52 acsd: eth6: Adjusted channel spec: 0xe09b (149/80)
06:27:52 acsd: eth6: selected channel spec: 0xe09b (149/80)
06:27:52 acsd: acs_set_chspec: 0xe09b (149/80) for reason APCS_INIT
06:27:53 acsd: acs_update_driver(440): acs update failed ret code: -22
06:27:53 acsd: acs_init_run(955): eth6: update driver failed

06:37:58 acsd: eth6: Selecting 5g band ACS policy
06:37:58 acsd: acs_update_driver(440): acs update failed ret code: -22
06:37:58 acsd: acs_set_initial_chanspec(380): eth6: update driver failed
06:37:58 wlceventd: wlceventd Start...
06:38:02 acsd: eth6: selected channel spec: 0xe09b (149/80)
06:38:02 acsd: eth6: Adjusted channel spec: 0xe09b (149/80)
06:38:02 acsd: eth6: selected channel spec: 0xe09b (149/80)
06:38:02 acsd: acs_set_chspec: 0xe09b (149/80) for reason APCS_INIT

我第一次看見是
1.無線 MAC 地址過濾器 - 頻段 2.4GHz
2.啟動 MAC 位址過濾 - 是
3.新増 一些 MAC 位址 - 套用本頁面設定
4.啟動 MAC 位址過濾 - 否 - 套用本頁面設定
5.無線 MAC 地址過濾器 - 頻段 5GHz
6.啟動 MAC 位址過濾 - 是
7.新増 一些 MAC 位址 - 套用本頁面設定
8.啟動 MAC 位址過濾 - 否 - 套用本頁面設定

然後留意到Chanspec: 5GHz channel 變成只有 20MHz
acs_update_driver(440): acs update failed是自動頻道頻寬升級失敗的意思 (ie.20MHz->80MHz)
5GHz我一直在用80MHz,硬件上當然沒問題,請貴公司處理好軟件的邏輯………

另外
雖然有說重要的東西說三次,但看Syslog, 貴公司的Router也喜歡重要的東西做三次？
例如
02:53:43 acsd: acs_set_chspec: 0x1008 (8) for reason APCS_CSTIMER
03:07:10 acsd: eth5: selected_chspec is 1003 (3)
03:07:10 acsd: eth5: Adjusted channel spec: 0x1003 (3)
03:07:10 acsd: eth5: selected channel spec: 0x1003 (3)
03:07:11 acsd: eth5: selected_chspec is 1003 (3)
03:07:11 acsd: eth5: Adjusted channel spec: 0x1003 (3)
03:07:11 acsd: eth5: selected channel spec: 0x1003 (3)
03:07:12 acsd: eth5: selected_chspec is 1003 (3)
03:07:12 acsd: eth5: Adjusted channel spec: 0x1003 (3)
03:07:12 acsd: eth5: selected channel spec: 0x1003 (3)
03:07:13 acsd: eth5: selected_chspec is 1003 (3)
03:07:13 acsd: eth5: Adjusted channel spec: 0x1003 (3)
03:07:13 acsd: eth5: selected channel spec: 0x1003 (3)

07:10-07:13四秒内同樣的一件事做四次,那是什麼保險之舉嗎

[有想過未來世青還叫小翼的問題嗎]

Moderator自己谷歌下,少人說但不代表軟件沒有問題

[STARRAIN_ASUS]

Hi 有想過未來世青還叫小翼的問題嗎（笑）,
請問是指操作 MAC 位址過濾設定後出現update driver failed，設定上5GHz channel 變成只有 20MHz，但您實際還是使用原設定的80MHz嗎？
5GHz channel 變成只有變成20MHz、實際使用是80MHz，是在syslog中出現，或以何種方式得知？
另請將使用路由器序號、韌體版本、網路架構圖、完整syslog提供給小編。
謝謝您。

[有想過未來世青還叫小翼的問題嗎]

>請問是指操作 MAC 位址過濾設定後出現update driver failed
是,歩驟如上

>設定上5GHz channel 變成只有 20MHz，但您實際還是使用原設定的80MHz嗎？
無線Syslog裏channel掉到20MHz，但實際『原設定』還是用20MHz/40MHz/80MHz/160MHz
雖然將WiFI開關一下（啟用無線網路 是>否>是）就上返80MHz了(手機/平板/筆電等只支持到80M)

>5GHz channel 變成只有變成20MHz、實際使用是80MHz，是在syslog中出現，或以何種方式得知？

實際也是20MHz
系統記錄 - 無線使用者 > 5G Stations List > 手機 > BW 20M

我再沒拈那個MAC 位址過濾後，Syslog就再没出現acs update failed
3.0.0.4.384_9354

Syslog沒什麼特別,5G ACS policy上面接2g band ACS policy,再上也是那些例牌的log
.
.
.
06:27:43 kernel: ubi2: mtd10 is detached
06:27:46 acsd: eth5: Selecting 2g band ACS policy
06:27:46 wlceventd: wlceventd Start...
06:27:49 acsd: eth5: selected channel spec: 0x1008 (8)
06:27:49 acsd: eth5: Adjusted channel spec: 0x1008 (8)
06:27:49 acsd: eth5: selected channel spec: 0x1008 (8)
06:27:49 acsd: acs_set_chspec: 0x1008 (8) for reason APCS_INIT
06:27:49 acsd: eth6: Selecting 5g band ACS policy
06:27:52 acsd: acsd_main_loop(1062): sync_id: 25035, status:1, misc.error/abort
06:27:52 acsd: eth6: selected channel spec: 0xe09b (149/80)
06:27:52 acsd: eth6: Adjusted channel spec: 0xe09b (149/80)
06:27:52 acsd: eth6: selected channel spec: 0xe09b (149/80)
06:27:52 acsd: acs_set_chspec: 0xe09b (149/80) for reason APCS_INIT
06:27:53 acsd: acs_update_driver(440): acs update failed ret code: -22
06:27:53 acsd: acs_init_run(955): eth6: update driver failed

[有想過未來世青還叫小翼的問題嗎]

正常時候是正常並沒錯誤
06:25:46 kernel: ubi2: mtd10 is detached
06:25:49 acsd: eth5: Selecting 2g band ACS policy
06:25:49 wlceventd: wlceventd Start...
06:25:52 acsd: eth5: selected channel spec: 0x100a (10)
06:25:52 acsd: eth5: Adjusted channel spec: 0x100a (10)
06:25:52 acsd: eth5: selected channel spec: 0x100a (10)
06:25:52 acsd: acs_set_chspec: 0x100a (10) for reason APCS_INIT
06:25:52 acsd: eth6: Selecting 5g band ACS policy
06:25:56 acsd: eth6: selected channel spec: 0xe09b (149/80)
06:25:56 acsd: eth6: Adjusted channel spec: 0xe09b (149/80)
06:25:56 acsd: eth6: selected channel spec: 0xe09b (149/80)
06:25:56 acsd: acs_set_chspec: 0xe09b (149/80) for reason APCS_INIT
06:27:23 wlceventd: wlceventd_proc_event(527): eth6: Assoc

06:53:22 acsd: acs_set_chspec: 0x1003 (3) for reason APCS_CSTIMER
06:57:10 acsd: eth6: selected_chspec is e03a (52/80)
06:57:10 acsd: eth6: Adjusted channel spec: 0xe03a (52/80)
06:57:10 acsd: eth6: selected channel spec: 0xe03a (52/80)
06:57:11 acsd: eth6: selected_chspec is e03a (52/80)
06:57:11 acsd: eth6: Adjusted channel spec: 0xe03a (52/80)
06:57:11 acsd: eth6: selected channel spec: 0xe03a (52/80)
06:57:12 acsd: eth6: selected_chspec is e03a (52/80)
06:57:12 acsd: eth6: Adjusted channel spec: 0xe03a (52/80)
06:57:12 acsd: eth6: selected channel spec: 0xe03a (52/80)
06:57:13 acsd: eth6: selected_chspec is e03a (52/80)
06:57:13 acsd: eth6: Adjusted channel spec: 0xe03a (52/80)
06:57:13 acsd: eth6: selected channel spec: 0xe03a (52/80)
06:57:17 wlceventd: wlceventd_proc_event(499): eth5: Auth
（為什麼要同一件事做四次, 我知很重要啦, 但為什麼...
啊～想到了,是20MHz+20MHz+20MHz+20MHz四個channel的Log?）

1.我只動過MAC 位址過濾, 怎知道為什麼會掉MHz
2.掉MHz也不是問題,但為什麼上不回去
31.動過MAC 位址過濾（開和關）後會引起什麼錯誤?
32.或是acs update driver機制邏輯有問題?
RSSI: 0 dBm SNR: 0 dB noise: -86 dBm 無線Syslog那個-86 dBm是環境雜訊吧
4.我又沒十幾二十個Router, 不可能人為地増加雜訊令它掉到20MHz後再測試能不能上回80MHz