[2020/04/27 13:00:08]
Ai 超頻調節 [D.O.C.P. Standard]
D.O.C.P. [D.O.C.P DDR4-3200 16-18-18-38-1.35V]
APU 頻率 [100.0000]
BCLK_Divider [自動]
Performance Enhancer [自動]
CPU Core Ratio [Auto]
Performance Bias [自動]
記憶體頻率 [DDR4-3200MHz]
FCLK Frequency [自動]
Core Performance Boost [自動]
SMT Mode [自動]
TPU [Keep Current Settings]
Precision Boost Overdrive [自動]
Max CPU Boost Clock Override [自動]
Platform Thermal Throttle Limit [Auto]
Mem Over Clock Fail Count [Auto]
記憶體 cas# 延遲 [16]
DRAM RAS# to CAS# Read Delay [18]
DRAM RAS# to CAS# Write Delay [18]
記憶體 RAS# 預充電時間 [18]
記憶體行有效至預充電最短週期 [38]
Trc [Auto]
TrrdS [Auto]
TrrdL [Auto]
Tfaw [Auto]
TwtrS [Auto]
TwtrL [Auto]
Twr [Auto]
Trcpage [Auto]
TrdrdScl [Auto]
TwrwrScl [Auto]
Trfc [Auto]
Trfc2 [Auto]
Trfc4 [Auto]
Tcwl [Auto]
Trtp [Auto]
Trdwr [Auto]
Twrrd [Auto]
TwrwrSc [Auto]
TwrwrSd [Auto]
TwrwrDd [Auto]
TrdrdSc [Auto]
TrdrdSd [Auto]
TrdrdDd [Auto]
Tcke [Auto]
ProcODT [自動]
Cmd2T [自動]
Gear Down Mode [自動]
Power Down Enable [自動]
RttNom [自動]
RttWr [自動]
RttPark [自動]
MemAddrCmdSetup [Auto]
MemCsOdtSetup [Auto]
MemCkeSetup [Auto]
MemCadBusClkDrvStren [Auto]
MemCadBusAddrCmdDrvStren [Auto]
MemCadBusCsOdtDrvStren [Auto]
MemCadBusCkeDrvStren [Auto]
CPU 負載線校正 [自動]
CPU 目前功能 [自動]
CPU VRM 切換頻率 [自動]
VRM 擴充頻譜 [自動]
負載控制 [T.Probe]
相數控制 [自動]
CPU Power Thermal Control [120]
VDDSOC Load-line Calibration [自動]
VDDSOC Current Capability [自動]
VDDSOC Switching Frequency [自動]
VDDSOC Phase Control [自動]
DRAM 電流容量 [100%]
DRAM 供電相位控制 [Extreme]
DRAM 切換頻率 [自動]
DRAM VBoot Voltage [Auto]
VTTDDR Voltage [Auto]
VPP_MEM Voltage [Auto]
DRAM CTRL REF Voltage on CHA [Auto]
DRAM CTRL REF Voltage on CHB [Auto]
VDDP Voltage [Auto]
1.8V Standby Voltage [Auto]
CPU 3.3v AUX [Auto]
2.5V SB Voltage [Auto]
DRAM R1 Tune [Auto]
DRAM R2 Tune [Auto]
DRAM R3 Tune [Auto]
DRAM R4 Tune [Auto]
PCIE Tune R1 [自動]
PCIE Tune R2 [自動]
PCIE Tune R3 [Auto]
PLL Tune R1 [自動]
PLL reference voltage [Auto]
T Offset [Auto]
Sense MI Skew [自動]
Sense MI Offset [Auto]
Promontory presence [自動]
Clock Amplitude [自動]
CLDO VDDP voltage [Auto]
APU 電壓 [Manual mode]
- CPU Core Voltage Override [1.30000]
CPU SOC Voltage [自動]
DRAM 電壓 [1.35000]
CLDO VDDG voltage [Auto]
1.8V PLL Voltage [Auto]
1.05V SB Voltage [Auto]
Firmware TPM [Disable]
Erase fTPM NV for factory reset [Enabled]
PSS Support [自動]
SVM Mode [已關閉]
主機板端指示燈 [開啟]
Q-Code LED Function [開啟]
SATA Port Enable [開啟]
SATA Mode [AHCI]
NVMe RAID mode [Disabled]
S.M.A.R.T.狀態偵測 [設定]
Hot Plug [已關閉]
Hot Plug [已關閉]
Hot Plug [已關閉]
Hot Plug [已關閉]
Hot Plug [已關閉]
Hot Plug [已關閉]
高傳真音效控制器 [開啟]
M.2_2 PCIe Bandwidth Configuration [自動]
PCIEX16/X8_1 Mode [自動]
PCIEX8/X4_2 Mode [自動]
PCIEX4_3 Mode [自動]
M.2_1 Link Mode [自動]
M.2_2 Link Mode [自動]
SB Link Mode [自動]
Asmedia USB 3.1 控制器 [開啟]
USB Type C 電源開關 [自動]
When system is in working state [開啟]
When system is in sleep, hibernate or soft off states [關閉]
Intel LAN 控制器 [設定]
Intel LAN OPROM [取消]
ErP 支援 [已關閉]
Restore On AC Power Loss [Power Off]
由 PCI-E/PCI 裝置喚醒 [已關閉]
由 RTC 喚醒 [已關閉]
網路堆棧 [已關閉]
裝置 [CT500MX500SSD1]
Legacy USB 支援 [Enabled]
XHCI Hand-off [Enabled]
KingstonDataTraveler 3.0 [Auto]
U31G2_EC3 [開啟]
U31G2_EA2 [開啟]
U31G2_E1 [開啟]
U31G1_1 [開啟]
U31G1_2 [開啟]
U31G1_3 [開啟]
U31G1_4 [開啟]
U31G1_5 [開啟]
U31G1_6 [開啟]
U31G1_7 [開啟]
U31G1_8 [開啟]
U31G1_9 [開啟]
U31G1_10 [開啟]
USB11 [開啟]
USB12 [開啟]
USB13 [開啟]
USB14 [開啟]
USB15 [開啟]
處理器溫度 [Monitor]
主機板溫度 [Monitor]
PCH Temperature [Monitor]
T_Sensor1 Temperature [Monitor]
EXT_Sensor1 溫度 [Monitor]
EXT_Sensor2 溫度 [Monitor]
EXT_Sensor3 溫度 [Monitor]
中央處理器風扇速度 [Monitor]
主機殼風扇 1 速度 [Monitor]
主機殼風扇 2 速度 [Monitor]
主機殼風扇 3 速度 [Monitor]
水泵轉速 [Monitor]
HAMP Fan Speed [Monitor]
中央處理器附加風扇速度 [Monitor]
水泵轉速 [Monitor]
Extension Fan 1 Speed [Monitor]
Extension Fan 2 Speed [Monitor]
Extension Fan 3 Speed [Monitor]
W_FLOW Speed [Monitor]
W_IN Temperature [Monitor]
W_OUT Temperature [Monitor]
中央處理器核心電壓 [Monitor]
3.3V 電壓 [Monitor]
5V 電壓 [Monitor]
12V 電壓 [Monitor]
處理器 Q-Fan 控制 [PWM Mode]
CPU Fan Smoothing Up/Down Time [0 sec]
CPU Fan Speed Lower Limit [200 RPM]
處理器風扇設定檔 [静音]
主機殼風扇 1 Q-Fan 控制 [PWM Mode]
Chassis Fan 1 Q-Fan Source [CPU]
Chassis Fan 1 Smoothing Up/Down Time [0 sec]
主機殼風扇 1 速度最低限制 [200 RPM]
主機殼風扇 1 設定檔 [静音]
主機殼風扇 2 Q-Fan 控制 [PWM Mode]
Chassis Fan 2 Q-Fan Source [CPU]
Chassis Fan 2 Smoothing Up/Down Time [0 sec]
主機殼風扇 2 速度最低限制 [200 RPM]
主機殼風扇 2 設定檔 [静音]
主機殼風扇 3 Q-Fan 控制 [PWM Mode]
Chassis Fan 3 Q-Fan Source [CPU]
Chassis Fan 3 Smoothing Up/Down Time [0 sec]
主機殼風扇 3 速度最低限制 [200 RPM]
主機殼風扇 3 設定檔 [静音]
HAMP Fan Q-Fan Control [自動]
HAMP Fan Q-Fan Source [CPU]
HAMP Fan Smoothing Up/Down Time [0 sec]
HAMP Fan Speed Low Limit [200 RPM]
HAMP Fan Profile [標準]
Extension Fan 1 Q-Fan Control [DC Mode]
Extension Fan 1 Q-Fan Source [CPU]
Extension Fan 1 Speed Low Limit [200 RPM]
Extension Fan 1 Profile [標準]
Extension Fan 2 Q-Fan Control [DC Mode]
Extension Fan 2 Q-Fan Source [CPU]
Extension Fan 2 Speed Low Limit [200 RPM]
Extension Fan 2 Profile [標準]
Extension Fan 3 Q-Fan Control [DC Mode]
Extension Fan 3 Q-Fan Source [CPU]
Extension Fan 3 Speed Low Limit [200 RPM]
Extension Fan 3 Profile [標準]
水泵控制 [已關閉]
PSPP Policy [自動]
快速啟動 [Enabled]
NVMe Support [Enabled]
AC 電源中斷後下一次開啟 [正常啟動]
AMI Native NVMe Driver Support [開啟]
開機圖示顯示 [開啟]
開機自我測試（POST）延遲時間 [3 秒]
啟動數字鎖定鍵狀態 [Enabled]
若出現錯誤等待按下 F1 鍵 [開啟]
附加固件資訊 [開啟]
捕捉中斷 19 [已關閉]
設定模式 [進階模式]
開啟相容性支援模組 [開啟]
可開機裝置控制 [UEFI 與傳統韌體]
從網路裝置啟動 [Legacy only]
從儲存裝置啟動 [Legacy only]
從 PCI-E 擴充卡啟動 [Legacy only]
作業系統類型 [其他作業系統]
設置動畫 [已關閉]
ASUS Grid Install Service [開啟]
名稱： []
儲存到檔案 [1]
CPU Core Voltage [Auto]
VDDSOC Voltage [Auto]
1.8V PLL Voltage [Auto]
BCLK Frequency [Auto]
CPU Ratio [Auto]
記憶體插槽 # [插槽 A2]
匯流排介面 [PCIEX16/X8_1]
Custom Pstate0 [Auto]
L1 Stream HW Prefetcher [Auto]
L2 Stream HW Prefetcher [Auto]
Core Performance Boost [Auto]
Global C-state Control [Auto]
DRAM ECC Enable [Auto]
DRAM scrub time [Auto]
Poison scrubber control [Auto]
Redirect scrubber control [Auto]
Redirect scrubber limit [Auto]
NUMA nodes per socket [Auto]
Memory interleaving [Auto]
Memory interleaving size [Auto]
1TB remap [Auto]
DRAM map inversion [Auto]
ACPI SRAT L3 Cache As NUMA Domain [Auto]
ACPI SLIT Distance Control [Auto]
ACPI SLIT remote relative distance [Auto]
GMI encryption control [Auto]
xGMI encryption control [Auto]
CAKE CRC perf bounds Control [Auto]
4-link xGMI max speed [Auto]
3-link xGMI max speed [Auto]
Disable DF to external IP SyncFloodPropagation [Auto]
Disable DF sync flood propagation [Auto]
CC6 memory region encryption [Auto]
Memory Clear [Auto]
Overclock [Auto]
Power Down Enable [Auto]
Cmd2T [Auto]
Gear Down Mode [Auto]
CAD Bus Timing User Controls [Auto]
CAD Bus Drive Strength User Controls [Auto]
Data Bus Configuration User Controls [Auto]
Data Poisoning [Auto]
DRAM Post Package Repair [Disable]
RCD Parity [Auto]
DRAM Address Command Parity Retry [Auto]
Write CRC Enable [Auto]
DRAM Write CRC Enable and Retry Limit [Auto]
Disable Memory Error Injection [True]
DRAM ECC Symbol Size [Auto]
DRAM UECC Retry [Auto]
TSME [Auto]
Data Scramble [Auto]
DFE Read Training [Auto]
FFE Write Training [Auto]
PMU Pattern Bits Control [Auto]
MR6VrefDQ Control [Auto]
CPU Vref Training Seed Control [Auto]
Chipselect Interleaving [Auto]
BankGroupSwap [Auto]
BankGroupSwapAlt [Auto]
Address Hash Bank [Auto]
Address Hash CS [Auto]
Address Hash Rm [Auto]
SPD Read Optimization [Enabled]
MBIST Enable [Disabled]
Pattern Select [PRBS]
Pattern Length [3]
Aggressor Channel [1 Aggressor Channel]
Aggressor Static Lane Control [Disabled]
Target Static Lane Control [Disabled]
Worst Case Margin Granularity [Per Chip Select]
Read Voltage Sweep Step Size [1]
Read Timing Sweep Step Size [1]
Write Voltage Sweep Step Size [1]
Write Timing Sweep Step Size [1]
IOMMU [Auto]
Precision Boost Overdrive [Auto]
Precision Boost Overdrive Scalar [Auto]
FCLK Frequency [Auto]
SOC OVERCLOCK VID [0]
UCLK DIV1 MODE [Auto]
VDDP Voltage Control [Auto]
VDDG Voltage Control [Auto]
SoC/Uncore OC Mode [Auto]
LN2 Mode [Auto]
ACS Enable [Auto]
PCIe Ten Bit Tag Support [Auto]
Max Voltage Offset [Auto]
cTDP Control [Auto]
EfficiencyModeEn [Auto]
Package Power Limit Control [Auto]
APBDIS [Auto]
DF Cstates [Auto]
CPPC [Auto]
CPPC Preferred Cores [Auto]
BoostFmaxEn [Auto]
Early Link Speed [Auto]